EAST ALABAMA MOTOR
2009 LIMITED SPORTSMAN TECHNICAL RULES
(FORMERLY SUPER STREET)
**Rules new for 2009 will be
highlighted in Blue.
**Please Note That Rule Changes Or Corrections, during
the season Will Be In Red
This division is open to any American manufactured automobile. NO convertibles,
station wagons or trucks.
WEIGHT:
A. 2800lb with driver, 3 Link rear suspension
B. 2900lb with driver, 4 link rear suspension.
C. 604 crate engine deduct 150lb. from any of above
combinations.
D. 602 crate engine deduct 300lb. from any of above
combinations.
E. Oversized valves add 50lbs.
F. All cars must have weight posted on right side of roof.
G. All GM crate engines must have factory GM seals or GM/RM seals, or Crate
ENGINE:
A. ONLY standard factory street production V-8 or V-6 engines allowed. 362
cubic inches maximum on small blocks and must utilize stock bore and stroke
combinations. 374 cubic inches maximum on Chrysler.
Unlimited cubic inches on large blocks must remain stock bore and stroke,
.060ths maximum overbore.
B. Blocks may be surfaced, and pistons may not exceed top of block more than
.010ths measured without head gasket. Ford and Chryslers may run dome pistons
when using stock factory production cylinder heads with stock size valves ONLY
when using World heads must use 2 valve relief flat top pistons ONLY.
C. All crankshafts must be factory steel or cast iron crankshafts with casting
numbers plainly visible. OEM replacement eagle or scat crankshaft, NO knife
edging or excessive lightening
48 lbs minimum weight. All cranks must remain
stock stroke to make and model of engine. Example, 350 Chevrolet 3.48 stroke
D. Engine balancing permitted.
E. Timing chains ONLY, no belt or gear drives.
F. NO dry sump oiling systems permitted. Single stage external oil pump
allowed, must pick up and return oil from oil pan NOT an external tank.
CONNECTING RODS:
A. Any sportsman steel connecting rod allowed. MUST remain stock length,
Example 350 Chevrolet must be 5.7 long. 6 rods are NOT permitted. Eagle
H-beam rod permitted, NO other H-beams allowed
B. NO titanium, aluminum, or any other exotic material permitted.
PISTONS:
A. Flat top 2 or 4 valve relief pistons ONLY. Ford must use these pistons when
using the World Product Windsor Sr. heads. Ford and Chrysler may use dome
piston when using stock factory production heads, with stock size valves ONLY.
CAMSHAFT:
A. Any flat tappet camshaft permitted. NO roller camshafts permitted.
B. Lifters must remain stock diameter, Example, Chevrolet .842
CYLINDER HEADS:
A. Any factory production steel head allowed. 062 or 906 GM Vortec
Heads allowed, Intake
runner 175cc max. exhaust runner 64cc max. World
products 4360 & 4361, and Windsor SR. heads
permitted. NO angle plug heads except Ford & Chrysler NO Bowtie, Dart, SVO
N series, or aluminum heads (except 604 crate motors.)
B. Chevrolet's 1.94 maximum diameter on intake valves and 1.5 maximum
diameter on exhaust. Ford Windsor Sr. OK Oversized valves add 50lb. All other
makes must use stock sized.
C. NO porting, polishing, squaring, or epoxying of
ports.
D. Multi-angled valve jobs permitted. Angle milling permitted.
E. Any valve retainer, and any spring permitted.
F. NO shaft mounted rocker systems permitted. All others permitted.
INTAKE:
A. Aluminum or cast iron intakes allowed.
B. NO porting, polishing, squaring, or epoxying
inside runners or plenum.
C. 1 spacer allowed between intake and carburetor. 602 crate engine may
run 2 spacer.
CARBURETOR:
A. One dual line Holley 750 cfm maximum Or EAMS spec carb. Carbs checked with no-go
gauges. No porting or polishing of venturies,
boosters or throttle bores.
B. Air horn may be removed, if not choke butterfly must be removed.
C. May drill idle holes in primary butterflies.
D. No gold claw, silver claw, or demon carbs.
E. Crate motors may use Holley 650cfm, down-leg 3/8 ID boosters allowed or EAMS
Spec Crate carb (EAMS Spec Crate carb
must be purchased at track and have track serial number on it.) Checked with go-no-go gauges.
FUEL SYSTEM:
A. Stock type fuel pumps ONLY mounted in stock location. NO belt driven or
electric pumps permitted.
B. NO ALCOHOL, NO NITROUS OXIDE, GAS ONLY.
C. Sunoco Blue, Sunoco purple or Sunoco GT98 unleaded only. Fuel must check +
or -5 on electric fuel checker when calibrated with EAMS track racing fuel.
D. Fuel that is burned at track must be bought at track.
IGNITION SYSTEM:
A. Any type electronic or breaker type ignition system permitted.
B. NO magnetos
EXHAUST SYSTEM:
A. Collector type headers ONLY. NO zoomies or Tri-Y
headers.
ENGINE POSITION:
A. 1 from center of jack bolt to #1 spark plug, NO Tolerance.
TRANSMISSION:
A. Standard 4 speed or automatic transmission. After market SAFETY bell housing
and automatic cases permitted.
B. NO
C. Transmissions must have 2 working forward and a reverse gear.
D. Bert or Brinn Transmission OK.
E. Ballspline
transmissions Mandatory to run a carbon fiber drive shaft. This is a safety
requirement. Must Have By May 1, 2009.
CLUTCH:
A. Multi-disc clutch assembly $600 cost limit. No aluminum flywheels.
B. All cars must have a workable clutch.
FRAME:
A. 104 wheelbase minimum, 1 tolerance.
B. Uni-body chassis may be connected
.
C. Frame and body do not have to be same make and model. Engine interchange
permitted.
D. Frame must be stock from front clip and have a minimum of 2 x 2, or 1 1/2x .090 Round steel
tubing from end of original front sub clip to rear bumper. Must use stock lower control arms mounted in
stock locations.
FRONT SUSPENSION:
A. Jack screws permitted.
B. Tubular upper control arms permitted.
C. 5 coil springs minimum mounted in stock location.
D. Racing shocks permitted. No single adjustable or double adjustable shocks. 1 shock per wheel only front and rear suspension.
E. NO rack & pinion steering allowed. Stock type steering
systems ONLY.
F. Safety spindles permitted. ½ wheel studs minimum 1 lug nuts mandatory.
REAR SUSPENSION:
A. Jack screws permitted.
B. Stock type, or Quick Change rear ends permitted.
C. Torque links or rubber snubber bar OK, 24 maximum
length mount to mount, 5th coils or
lift bars OK, must
be one or the other, not both.
D. Any type trailing arms or leaf springs.
E. Safety spindles permitted. ½ wheel studs minimum 1 lug nuts mandatory.
BODY:
A. Aluminum or fiberglass bodies allowed. All bodies must have stock appearing
nose pieces. NO wedge bodies.
B. 76" maximum width front to rear. Quarter
panels must be 45" long maximum with a maximum height of 37".
C. Light tube bracing behind bumpers. NO pipes, or
push bars in front of bumpers.
D. 72" maximum width of spoiler, 8" maximum height, 8" maximum
width on side pods.
E. Crate motor 10" spoiler permitted, 10
maximum height, 18 maximum width on spoiler supports.
F. Must have front and rear tow hooks.
WHEELS AND TIRES:
A. Any Wheel, 12 maximum width.
B. Bead locks allowed on right rear ONLY.
C. Wide 5 wheels and adapters permitted.
D. Track tire EAMS Spec/crate D21 or spec/crate
D55 Hoosier Racing Tires only.
E. No inner liners.
F. No tire softeners permitted. Tires will be subject to durometer hardness
test at any time to determine legality.
SAFETY:
A. All cars must meet the safety requirements as outlined in Section D of General
Track Rules for all Divisions.
PROTEST
A. Top End $250 - $50 will be retained by track.
B. Bottom End $250 - $50 will be retained by track.
C. Must protest Top End to protest Bottom End.
D. Visual protest $25 - $25 will be retained by track.
E. Crate motors may be protested.
Full Jig Limited Sportsman
Beginning in 2009 Full Jig Frames
may compete in the Limited Sportsman Division on a weekly basis, under the
below engine and chassis package ONLY.
WEIGHT:
A. 2650lb with driver. NOTE: Weight may be adjusted as season progresses
in the interest of fair competition to everyone.
B. All cars must have weight posted on right side of roof.
ENGINE:
A. ONLY standard factory 602 GM sealed Crate Engines, Engines must have
original seals or GM/RM seal bolts, or Crate
CARBURETOR:
A. One dual line Holley 650 CFM maximum. Holley HP 80541 ONLY, NO aftermarket
makes or parts, Must have all Holley numbering system, or EAMS Spec Crate carb (EAMS Spec Crate carb must be purchased at track and have track serial
number on it.)
B. 1 Carburetor Spacer ONLY,
allowed with this chassis package.
C. No Porting or Polishing of
Carburetor, Checked with GO-NO GO gauges.
FUEL SYSTEM:
A. Stock type fuel pumps ONLY mounted in stock location. NO belt driven or
electric pumps permitted.
B. NO ALCOHOL, NO NITROUS OXIDE, GAS ONLY.
C. Sunoco purple or Sunoco GT98 unleaded only. Fuel
must check + or -5 on electric fuel checker when calibrated with EAMS track
racing fuel.
D. Fuel that is burned at track must be bought at track.
IGNITION SYSTEM:
A. Stock type HEI distributor that comes with 602 ONLY. No aftermarket modules, or coils, or
distributor housings.
B. NO magnetos, NO 6AL or 6A type ignition boxes.
EXHAUST SYSTEM:
A. Collector type headers ONLY. NO zoomies or Tri-Y
headers.
ENGINE POSITION:
A. 6 ½ from center of ball joint to #1 spark plug, ½ tolerance. 50lb weight penalty for every ½ out of
tolerance mounted in front of water pump.
TRANSMISSION:
A. Standard 4 speed or automatic transmission. After market SAFETY bell housing
and automatic cases permitted.
B. Bert or Brinn Transmission OK.
C. Transmissions must have 2 working forward and a reverse gear.
D. NO
REAR END:
A. Standard quick change rear end
permitted. No Titanium or exotic
material axles, spools, gears, or other materials inside rear end.
FRAME:
A. 103 wheelbase minimum, 1 tolerance.
B. Any Late Model Chassis allowed,
Square tube or Round tube. NO aluminum frames or front clips on chassis, square
tube frames must be a minimum of 2x 2 tubing, round tube must be a minimum of
1 Ύ tubing. Full racing roll cage
mandatory, 1 ½ OD x .090 steel tubing minimum. No chrome moly
tubing.
C. One working shock per wheel. NO
Single adjustable, or double adjustable shocks
allowed. NO canister style or remote adjustable shocks permitted. NO externally
adjustable shocks.
D. May run 1 of the following rear
suspensions, 5th coil or torque link, NOT both. 1 90/10 shocks
allowed to be mounted top of rear end.
BODY:
A. S.A.S.. World of Outlaw, Crate Racin USA, Fastrak, or NLMS Body rules
apply.
B. 8 Spoiler Maximum with 8
spoiler supports maximum, must meet above rules.
WHEELS AND TIRES:
Same as Above
SAFETY:
A. All cars must meet the safety requirements as outlined in Section D of
General Track Rules for all Divisions.